TML - 1640
TML - 1660
All models with one piece solid stand
All models with universal feed gearbox & reversable apron
All models meet CE. (on request)
All models with 52.5mm (2.066") spindle bore, ASA D1-6
- All castings are properly stabilized and stress relieved.
- Bed ways are hardened & ground to min. HS-70.
- Turcite B coating between the bed and carriage.
- Extremely low noise level.
- Foot brake pedal provided.
- Built-in coolant pump & fitting provided.
- Wider bed way which give absorbs vibration.
- Housing is vibration-absorbent, deflection-free.
- Gears are hardened & MAAG or REISHAUER ground.
- Universal type allowing a wide range of inch, metric, M.P., D.P. threads without change gears.
- R/H or L/H wheel can be available on request.
- Integrated automatic control for longitudinal & cross feeds, forward & reverse feeds.
CARRIAGE & SLIDE
- Anti-Float design backlash eliminator fitted in cross slide nut.
- Safety clutch at feed shaft.
- One shot lubrication in carriage & top slide.
- Dual dials supply inch system screw.
- Metric dial supply metric system only.
- Nylon safety gears in end train.
- Shear pin in leadscrew.
HEAVY DUTY SPINDLE.
- Machined from forged alloy steel, hardened ground & dynamically balanced.
- Three point support by high grade precision, machine tool taper roller & ball bearings.
- Backplate for 9" chuck
- Dead center MT.4
- Dead center MT.4 with carbide tip
- Spindle center sleeve MT.6
- Level pads......6 pcs
- Tool set & Box
- Operation manual & parts list
- 3-Jaws scroll 9" chuck
- 4-Jaws independent 10" chuck
- 5C collet closer attachment
- 5C collets (metric or inch)
- Driving plate with dog
- Chuck safety guard
- Hydraulic copying attachment
- Tool post grinder attachment
- Taper turning attachment
- Electrical system for CE
- Protect cover on leadscrew for CE
- Steady rest w/ball bearing
- Follow rest w/bronze tip
- Faceplate 12"
- Drill chuck & arbor
- Rotating center MT.4
- Halogen lamp
- Quick change tool post
- Carriage micro stop set
- Digital read out system
- Full length splash guard
|Capacity||Height of centers||205mm (8.07")|
|Swing over bed||O410mm (16.14")|
|Swing in gap||O583mm (22.95")|
|Swing over cross slide||O262mm (10.3")|
|Distance between centers||1000mm (40")||1500mm (60")|
|Width of bed||260mm (10.236")|
|Gap width in front faceplate||135mm (5.31")||225mm (8.85")|
|Spindle nose, internal taper||D1-6 / A1-6 (opt.), MT. No.6|
|Spindle center sleeve||MT. No.6 x MT. No.4|
|Spindle bore||O52.5mm (2.066")|
Gear steps / Range
|12 steps / 36~1800 R.P.M.|
|L||36 50 70 105|
|M||130 180 250 380|
|H||620 900 1200 1800|
|Carriage||Length on bed / Width of carriage||513mm (20.19") / 412mm (16.22")|
|Cross slide travel||220mm (8.6")|
|Top slide travel||125mm (4.92")|
|Threads and Feeds||Whitworth threads: Kinds / Range||45 Kinds / 2~72 T.P.I.|
|Metric threads: Kinds / Range||39 kinds / 0.2~14 mm|
|D.P. threads: Kinds / Range||21 kinds / 8~44 D.P.|
|M.P. threads: Kinds / Range||18 kinds / 0.3~3.5 M.P.|
|Longitudinal feeds||0.05~1.7 (0.002"~0.067")|
|Cross feeds||0.025~0.85 (0.001"~0.034")|
|Tailstock||Quill diameter||O52mm (2.47")|
|Quill travel||152 mm (6")|
|Taper of center||MT. No.4|
|Motor||Main spindle||5 HP|
|Coolant pump||1/8 HP|
|Measurement||Weight (Net / Gross) Approx.||1500kgs / 1620kgs||1600kgs / 1760kgs|
|Packing sizes||Length||2270mm (89.4")||2785mm (109.7")|
|Width x Height||Width 1120mm (44.1") x Height 1900mm (74.8")|
Specifications subject to change without notice.